Recent Content by pmcgee

  1. pmcgee
    Post

    C & S Peace & co

    From online ... from ebay I think ... https://goo.gl/photos/k9Xz3mCejtEw4wpD8
    Post by: pmcgee, Dec 15, 2016 in forum: Forum: Saw Identification and Discussion
  2. pmcgee
    Post

    GRMN Steel (Davenport)

    Here is a handsaw with just the tiny writing "DAVENPORT" "GRMN STEEL". I don't usuallt like this handle style so much, but this saw is sharp and...
    Post by: pmcgee, Oct 2, 2015 in forum: Forum: Saw Identification and Discussion
  3. pmcgee
    Post

    Domed Nut Saw ID

    I seen quite a few *like* it, but never a right-angle before ... excepting perhaps one S&J I can't quite recall now.
    Post by: pmcgee, Oct 2, 2015 in forum: Forum: Saw Identification and Discussion
  4. pmcgee
    Post

    Domed Nut Saw ID

    Do you know of any other handles with that severe of a drop?
    Post by: pmcgee, Sep 24, 2015 in forum: Forum: Saw Identification and Discussion
  5. pmcgee
    Post

    Saw Medallions

    A bit nicer version of the SD left-facing beaver ...
    Post by: pmcgee, Aug 17, 2015 in forum: Forum: Saw Identification and Discussion
  6. pmcgee
    Post

    Finally have the time to go through my stack...

    Very nice. :)
    Post by: pmcgee, Aug 17, 2015 in forum: Forum: Saw Identification and Discussion
  7. pmcgee
    Post

    James Robinson & Sons?

    "Although only one of James’ sons followed him into the business ..." ... don't give me that ... :p I dunno ... sounds kinda tempting ......
    Post by: pmcgee, Jul 31, 2015 in forum: Forum: Saw Identification and Discussion
  8. pmcgee
    Post

    Saw ID with "Our Daisy" Etch

    The handle distinctly resembles this EM Boynton from this forum ... although maybe a bit later and less refined. [IMG]
    Post by: pmcgee, Jul 31, 2015 in forum: Forum: Saw Identification and Discussion
  9. pmcgee
    Post

    Carbide Drill-bits

    They don't have time to eat it ... they're tunneling through it to get to a ... ?? turnip? mouse? How'dya think they make Swiss cheese? :)
    Post by: pmcgee, Jul 20, 2015 in forum: Forum: Saw Identification and Discussion
  10. pmcgee
    Thread

    Carbide Drill-bits

    Ray gave me this link earlier in the year and they drilled saw-plate like a hungry otter through cheese. (Perhaps a little indentation to start...
    Thread by: pmcgee, Jul 19, 2015, 3 replies, in forum: Forum: Saw Identification and Discussion
  11. pmcgee
    Post

    Disston "10"

    "Henry Disston ... he's just this guy, you know."
    Post by: pmcgee, Jul 7, 2015 in forum: Forum: Saw Identification and Discussion
  12. pmcgee
    Post

    Disston "10"

    Occasionally we can take a step back from squinting at etches and stamps, twisting and curving the blades to coax out the last vestiges of...
    Post by: pmcgee, Jul 7, 2015 in forum: Forum: Saw Identification and Discussion
  13. pmcgee
    Post

    Disston "10"

    I see the Disstonian site gives 1874 for the introduction of the Choice "80" with skewed back.
    Post by: pmcgee, Jul 6, 2015 in forum: Forum: Saw Identification and Discussion
  14. pmcgee
    Post

    Disston "10"

    I'm all in favour of Wild Ass Guesses, speculation and musings. :) Regardings 'and Sons' ... there's a kinda "fullstop" there that could be part...
    Post by: pmcgee, Jul 5, 2015 in forum: Forum: Saw Identification and Discussion